Industrial Services Info


Mechanical, electrical, controls, engineering, construction, predictive and preventive maintenance, and mechanical maintenance staffing are some of the services provided to industrial facilities.

With more than 20 years industrial plant support experience Cox-Powell provides turnkey projects, augment existing plant labor force, respond to emergency and non-emergency situations with service personnel, perform diagnostics and work in conjunction with other contractors.

DESIGN – RENOVATION – CONSTRUCTION

> Production Equipment
      Installation & Relocation
> Utilities
> Process Improvements
> Energy Solutions
> Paint Booths
> Fume Hoods

MECHANICAL

> Process Cooling
> Compressed Air
> Chilled Water
> Ventilation
> Air & Water – Testing,
      Adjusting & Balancing (TAB)
> Building Pressurization
> Clean Rooms and Isolation Rooms
> Piping
> Plumbing

METAL FABRICATION

> Industrial & HVAC Duct Design,
      Fabrication & Installation
> Capture Hoods
> Certified, Mig, Tig & Stick Welding



Our engineers participate with Plant Engineering and Maintenance in quality and process improvements, start-up, planned shoutdowns, and mechanical and electrical OSHA / EPA safety audits.





Industrial Services Sample Projects

-INJECTION MOULDING EQUIPMENT RELOCATION
Performed relocation all process equipment to a single plant. Moved 36 injection molding presses, chillers, pumps, and ancillary equipment. Installed compressed air, chilled water, and city water to each press. For the additional process requirements added chillers, pumps, controls, electrical, and storage tanks. For improved comfort in the production area installed ventilation fans and modified the existing plant make up air system. To allow for uninterrupted manufacturing during the consolidation much of the work was performed after hours and during weekend non-production hours.

-INSTALL GRIEVE WALK-IN OVEN
Set and leveled a new grieve walk-in oven. Installed gas line to the oven including all piping, fittings, regulators and valves. Tied in the electrical service from the existing 460 volt 30 amp disconnect. Used existing roof penetrations for the required vent and sealed all roof penetrations watertight.

-COIL WINDING MACHINES RELOCATION
Disconnected and reinstalled coil winding machines. Project included tag-out, plugging and labeling all electrical circuits, airlines, oxygen lines, acetylene lines and computer communication lines. Rerouted, installed and labeled new air lines, oxygen lines, acetylene lines and electrical circuits to new equipment locations and final connections. Covered all new lines on the floor with Diamond Deck metal anchoring it to the floor and applying black/yellow safety tape where the metal crosses walkways. Aligned, leveled and anchored the equipment. Ground and cut the existing anchors to floor level.

-PLANT RELOCATION & NEW PLANT HVAC / ELECTRICAL
Assisted in design, engineering and installation of HVAC and electrical for a 45,000 square foot shell building. Selected and installed two air-cooled chillers, three commercial rooftop units, one split system, associated ductwork, registers, grilles and temperature control systems. Relocated the Research and Development and Light Soak areas from the existing facility. This move included many pieces of laser machinery, gas cabinets and compression test chambers. For the Light Soak area the air compressor, associated drier, tank and piping were installed and six air cooled condensers and the environmental chambers were reinstalled. All equipment rigging, nitrogen piping, de-ionized water, chilled water, control cabinets, switchgear, electrical and programmable Logic Controller (PLC) panels were part of this move. Tied in domestic water and sewer piping for the HVAC equipment as well as insulation for all chilled water piping and ductwork, roofing penetrations and equipment rigging. Electrical service included new switchgear, a 300-amp busway as well as electrical panels, 4000 amp service, underground conduits and wiring and parking lot pole lighting. For the gas bunkers adjacent to the building several hundred feet of high-pressure gas lines, control units and ventilation were installed.

Service or Estimate Request

Service or Estimate Request

For our afterhours and emergency services please call 877-321-3212.

You will be connected immediately and our technician will respond to your call.

Note: * indicates a required field